AFCA Forums Home
Home Search search Menu menu Not logged in - Login | Register
AFCA Forums > Antique Fan Collectors Association > Buy-Sell-Trade > Westinghouse 516909A part needed

 Moderated by: Steve Cunningham, Rod Rogers, Larry Hancock
New Topic Reply Printer Friendly
Westinghouse 516909A part needed  Rate Topic 
AuthorPost
 Posted: Fri Feb 17th, 2017 03:04 am
  PMQuoteReply
1st Post
Steve Butler
AFCA Member


Joined: Wed Jul 6th, 2016
Location:  
Status: 
Offline
Hello all. My mother in law received this fan a long time ago when she worked for Westinghouse. My wife had never even seen it before. My father in law found it in the attic and gave it to me. My wife's mom is getting in worse health all the time and I want to give this back to her in working condition. I was able to get it running on all three speeds. I "just" need the pot metal piece that goes between the motor and the base. I'm holding it back together in the pictures to show what I need. Thanks for any help. It means a lot to get it back to her.  I almost forgot, I could use a rear bearing retainer too.  If you have a complete base that would be fine too. Steve

Attached Image (viewed 145 times):

image.jpg

Last edited on Fri Feb 17th, 2017 12:17 pm by Steve Butler

Back To Top PMQuoteReply  

 Posted: Fri Feb 17th, 2017 03:05 am
  PMQuoteReply
2nd Post
Steve Butler
AFCA Member


Joined: Wed Jul 6th, 2016
Location:  
Status: 
Offline
Tag

Attached Image (viewed 144 times):

image.jpg

Back To Top PMQuoteReply

 Posted: Fri Feb 17th, 2017 03:06 am
  PMQuoteReply
3rd Post
Steve Butler
AFCA Member


Joined: Wed Jul 6th, 2016
Location:  
Status: 
Offline
Another view 

Attached Image (viewed 143 times):

image.jpg

Back To Top PMQuoteReply  

 Posted: Fri Feb 17th, 2017 03:09 am
  PMQuoteReply
4th Post
Steve Butler
AFCA Member


Joined: Wed Jul 6th, 2016
Location:  
Status: 
Offline
Rear bearing retainer 

Attached Image (viewed 140 times):

image.jpg

Back To Top PMQuoteReply

 Posted: Fri Feb 17th, 2017 11:47 pm
  PMQuoteReply
5th Post
Darrell Koller
AFCA Member
 

Joined: Sat Oct 3rd, 2015
Location:  
Status: 
Offline
Hey Steve, I may have the rear bearing.  I'll check when I get home later. 
Can you post a picture of the base.  I have several bases that have already been powder coated that might work for you - thought I think they are from much older fans.

 ---Darrell

Last edited on Fri Feb 17th, 2017 11:49 pm by Darrell Koller

Back To Top PMQuoteReply  

 Posted: Sat Feb 18th, 2017 01:44 am
  PMQuoteReply
6th Post
Steve Butler
AFCA Member


Joined: Wed Jul 6th, 2016
Location:  
Status: 
Offline
Thanks Darrell. Here is the base.  I thought if someone had a bad motor and they were parting one out, the complete base would be good. The motor lifts out of the pivot piece. If the pivot was still in the base that would work. A base only won't get me any closer. I have the broken bearing piece and the cover. I can reuse them if necessary. There again, I would take it all if someone has everything together. In case it helps, this is a micarta blade fan non oscillating. I know it's probably not worth the effort but it's all about the sentimental value. Thanks for any help.  

Attached Image (viewed 104 times):

image.jpg

Back To Top PMQuoteReply

 Posted: Sat Feb 18th, 2017 01:45 am
  PMQuoteReply
7th Post
Steve Butler
AFCA Member


Joined: Wed Jul 6th, 2016
Location:  
Status: 
Offline
End cap 

Attached Image (viewed 103 times):

image.jpg

Back To Top PMQuoteReply  

 Posted: Sat Feb 18th, 2017 06:17 am
  PMQuoteReply
8th Post
Darrell Koller
AFCA Member
 

Joined: Sat Oct 3rd, 2015
Location:  
Status: 
Offline
Hey Steve,
I checked my "inventory".  All the bases that I have are for oscillators.  I think that I do have the rear bearing and carrier.  Let me know if you want it.

Also, all the necks/pivots that I have are also for oscillators.
---Darrell


 

Last edited on Sat Feb 18th, 2017 06:18 am by Darrell Koller

Back To Top PMQuoteReply

 Posted: Sat Feb 18th, 2017 01:04 pm
  PMQuoteReply
9th Post
Steve Butler
AFCA Member


Joined: Wed Jul 6th, 2016
Location:  
Status: 
Offline
Thanks Darrell. I appreciate the effort. I will let you know. The pivot is the make or break item for now. 

Back To Top PMQuoteReply  

 Posted: Sun Feb 19th, 2017 07:06 am
  PMQuoteReply
10th Post
Charlie Forster
AFCA Member


Joined: Sun Jul 13th, 2014
Location:  
Status: 
Offline
You might try Mike Holland

Back To Top PMQuoteReply

Current time is 10:46 pm  
AFCA Forums > Antique Fan Collectors Association > Buy-Sell-Trade > Westinghouse 516909A part needed Top



Beige Theme By: Di @ UltraBB
UltraBB 1.17 Copyright © 2007-2008 Data 1 Systems
Page processed in 0.1841 seconds (11% database + 89% PHP). 27 queries executed.